Forum Post: Cable symbol for Single Line Mode
Hi, I'd like to create symbol for cable to represent it on Single Line Mode diagram (overview to cables used in project). 1. Which symbol type should be used? Just "cable" as for Schematic Mode? I...
View ArticleForum Post: RE: Drawing Cable Trays vertically
Hi Philipp, For drawing cable trays vertically you can use Place Part tool available in Raceway Router. While Routing a cable tray, after placing a datapoint place part can be found in dialog box that...
View ArticleForum Post: RE: Cable symbol for Single Line Mode
Hi WojtekM, The same cable symbol as used in schematic mode can be used in Single Line diagram Mode. You have to assign a family to the cable, and its cross reference has to be defined in Wiring...
View ArticleForum Post: RE: Drawing Cable Trays vertically
Thank you for your reply, I meant more how to draw the whole tray routing horizontally. But that option is still very helfpul, thanks. Also I assume for the Raceway Generator, it always converts the...
View ArticleForum Post: RE: Cable symbol for Single Line Mode
Hi Lalitesh, thanks for your reply. [quote userid="1018826" url="~/products/electrical___instrumentation/f/elcocad-promis-e-forum/185393/cable-symbol-for-single-line-mode/543342"]However to show...
View ArticleForum Post: Calculate total lenght of cables
Hi, in a project there's a lot o cables, each of them has attribute "Length" properly filled: How to generate report, calculating total cable lenght for each part number? Regards, Wojtek
View ArticleForum Post: RE: Calculate total lenght of cables
Hi WojtekM, We will investigate your concern and will provide you an update.
View ArticleForum Post: RE: Cable symbol for Single Line Mode
Hi Wojtek, For the concern of adding free cores in the report you can design the report template according to your requirements. This can be done by using Report Template Designer . Go to Manage...
View ArticleForum Post: RE: Cable symbol for Single Line Mode
Hi Lalitesh, [quote userid="1018826" url="~/products/electrical___instrumentation/f/elcocad-promis-e-forum/185393/cable-symbol-for-single-line-mode/543718"] In the table cell tasks the report cells can...
View ArticleForum Post: What function do the "Attribute" table in the part database have?
In the iec_parts_database.mdb file there is a table called "Attribute" (as seen below). I can't seem to find any information or figure out what it is used for. So my questions are: What function do the...
View ArticleForum Post: RE: What function do the "Attribute" table in the part database...
Hi Petter, Basically it provides the attribute information associated with symbols. The Attribute table in the parts database is used for some specific symbols which have specific attributes. For...
View ArticleForum Post: RE: What function do the "Attribute" table in the part database...
Thanks for the input! Unfortunately I don't feel like it answered my questions. To clarify, my iec_parts_database.mdb has a table named "Attributes" (in a fresh installation). This is the table I would...
View ArticleForum Post: Upgrading Promise from v8i to CONNECT edition. What's the correct...
Upgrading Promise from v8i to CONNECT edition. What's the correct order of tasks for a multi-user environment? Our company currently uses Promise V8i. We're going to migrate to CONNECT edition. There...
View ArticleForum Post: RE: Upgrading Promise from v8i to CONNECT edition. What's the...
Hi Dough, Yes you need to migrate your projects to Connect Edition, You can use the above link for migration of projects from V8i to CONNECT. But once the project are updated to connect edition they...
View ArticleForum Post: RE: Upgrading Promise from v8i to CONNECT edition. What's the...
Thanks Satish, I've just looked into the "Upgrade Project Database" option from within Promise CONNECT, can you confirm that operation will upgrade existing projects because, even though I've made a...
View ArticleForum Post: RE: Upgrading Promise from v8i to CONNECT edition. What's the...
Hi Dough, Since you have mentioned currently you are using Promis.e SS6 (08.11.11.18) can you confirm if it is AutoCAD based Promis.e or Power Platform Based ? If it is AutoCAD based Promis.e then you...
View ArticleForum Post: RE: Upgrading Promise from v8i to CONNECT edition. What's the...
Satish, Thanks for the useful info. My signature was a little out of date. I am using Standalone V8i, Select series 7. 08.11.12.18. I've updated my signature to show the correct version of Promise. I...
View ArticleForum Post: RE: Upgrading Promise from v8i to CONNECT edition. What's the...
Dough, The issue might be with selection of WorkSet under the WorkSpace as you need to specify the WorkSet for the Project as well to be migrated also. And if you have backup of Promis.e V8i SS7...
View ArticleForum Post: RE: Upgrading Promise from v8i to CONNECT edition. What's the...
Hi Satish, I haven't setup a workspace yet. It selected a workspace but that is only a reminant of a previous Promise CE installation that went wrong and got uninstalled. Also, I have no workset...
View Article